English Part Names Top Left side Front 3 4 6 Back 1 2 Right side 7 5 8 9 a c b 1 Power Port Connect the power cable. 2 2nd Camera Connection Terminal Use the 2nd camera connection cable (included with the 2nd camera (sold separately)) to connect to the connection terminal on the 2nd camera (sold separately). 3 microSD Card Slot 4 System Indicator 5 LCD 6 Function Buttons 7 Speaker 8 Microphone 9 Reset Button Press this button with the tip of a ballpoint pen to reset this product. a Angle Adjustment Jog Dial The angle of the lens can be adjusted by turning this dial. b Lens Pioneer polarized filter AD-PLF100 (sold separately) can help reduce reflections of the dashboard onto the windshield, and enable the capture of high- contrast videos. c Mounting Bracket Status Display The status display shows the operating status of this product. 1 2 3 45 6 7 00:00 1 Recording in progress 2 Elapsed recording time 3 Event recording status*1 4 Parking mode 5 Sound recording*2 6 Wi-Fi connection status*3 7 GPS reception status*4 *1 When manual event recording is performed, or vibration, sudden braking or an approaching vehicle behind is detected in the event recording mode, and event recording has been activated, “×2” is displayed. *2 A red “\” is displayed when sound recording is set to off. *3 During a Wi-Fi connection, this is displayed in green, and when Wi-Fi is disconnected, this is displayed in white. A red “x” is displayed when Wi-Fi connection is set to off. *4 During GPS reception, this is displayed in green, and when GPS cannot be received, this is displayed in white. In Parking Mode, a red “x” is displayed since GPS reception is set to off. System Indicator Display The operating status of this product is displayed with the system indicator. System Indicator MDuerniungDPislpaylabyaecdk/ Illuminated green ― Illuminated red ― Blinking red ― Video Recording ○ ― ― Recording Event ― ○ ― Under parking surveillance ○ ― ― Error Has Occurred (Including microSD Card not Inserted) ― ― ○ Function Buttons The functions of the function buttons are indicated by the icons displayed at the bottom of the screen. The functions of the buttons will depend on the displayed screen. (Icons are not displayed on some screens.) In the playback screen or MENU screen, pressing the function button returns you to the previous screen. ■ Recording 12 3 4 1 Main menu display 2 Switching of camera video* Hold down to switch Wi-Fi on/off 3 Take photo Hold down to switch microphone on/off 4 Manual recording of events * Switching between the Dash Camera main unit image and the 2nd camera (sold separately) image is only possible if the 2nd camera (sold separately) is connected. ■ During playback 5 Back 6 Previous file 7 Next file 8 Play/stop, delete 56 7 8 ■ During MENU screen display 9a b c 9 Back a Up* Hold down to switch Wi-Fi on/off b Down* Hold down to switch microphone on/off c Confirm * When the volume or sensitivity MENU screen is displayed, increase or decrease the volume or sensitivity. Inserting and Ejecting the microSD Card Turn off the power to this product when inserting and removing the microSD card. Inserting the microSD Card Hold the top edge of the microSD card, position the microSD card so that the label is facing the backside of this product, and slowly insert it into the microSD card slot until it clicks. Ejecting the microSD Card Slowly push in the top edge of the microSD card until it clicks ( 1 ). The lock will be released. Pull out the microSD card ( 2 ). CAUTION • Do not insert the microSD card at an angle. Doing so may cause damage. CAUTION • Ensure care is taken when handling the microSD card, as it could become hot after being written. Exclusive App The exclusive app “Dash Camera Interface” can be used to check the video recorded on this product or make settings on the screen of an iPhone or smartphone (Android™). To use this app, a Wi-Fi connection must be made between this product and iPhone/smartphone (Android™) beforehand. 1 Set the Wi-Fi function of this product to on. 2 Start the exclusive app from your device. 3 Operate the iPhone or smartphone (Android™) to select this product as the Wi-Fi connection device. The SSID name (access point name) and password of this product can be checked in the Wi-Fi settings screen. • Only one iPhone/smartphone (Android™) device can be connected to this product at one time. When a second device is connected, the first device will be disconnected. • While a Wi-Fi connection is made, no operations can be performed on this product. If a function button is pressed while a Wi-Fi connection is made, a message will be displayed prompting you to break the Wi-Fi connection. If you select [Yes], the Wi-Fi connection will be disconnected, and operations on this product will be enabled. • You can change the SSID name of this product by operating the exclusive app “Dash Camera Interface”. • It is recommended to enter the search term “Dash Camera Interface” in the search field to search for the application. Dash Camera Interface Check the Accessories Main Unit×1 Mounting Bracket×1 Power Cable (5 m)×1 Quick Start Guide×1 Warranty×1 Cleaning Cloth×1 Installation Specified Installation Position on Front Windscreen When installing this product the inside of the front windscreen, install in a vehicle and in a position that satisfies all of the following conditions. • A position where this entire product is within 20 % of the top edge of the height of the front windscreen (range within 20 % of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or are in the shadow of the rear view mirror as viewed from the driver’s seat. Note that “20 %” as described above is a rough estimate. Please install the product in accordance with your country’s laws and regulations. • A position where the lens part of this product is within the wiping range of the wiper. • A position where the lens part of this product does not hang over the sunshade and black ceramic lines/black ceramic pattern. • A position where this product faces in the horizontal direction to the front and side to side. • A position where the power cable can be routed without unnecessary force. This product Installation Angle Forward Direction of Vehicle Allowable Installation Angle: 30° to 60° (With Lens Horizontal) Installation Direction This product Horizontal Direction Front Windscreen *Install this product in a location where it will not interfere with the driver’s field of view,such as behind the rear view mirror. Front Windscreen Within 20 % of Height Ground This product Horizontal Direction A Pillar Rear View Mirror This product Range of Windscreen Wipers A Pillar Air Bag IMPORTANT • Always install this product in the specified installation position to ensure a safe field of view while driving and to achieve full performance from the product. • For vehicles equipped with driver-assistance systems, there may be areas where the installation of accessory items is prohibited. For details, please refer to the instruction manual of your vehicle. • Installing the Dash Camera main unit or cables near the film antenna element may affect the TV reception sensitivity. Recommended Installation Position on Rear Windscreen For installation on the rear glass, a 2nd camera (sold separately) is required. If installing only this product, then skip the instructions regarding installation on the rear glass. When installing the 2nd camera (sold separately) on the inside of the rear window, installation in a vehicle and in a position that satisfies all of the following conditions is recommended. • A position where the lens part of the 2nd camera (sold separately) is within the wiping range of the wiper. • A position where the 2nd camera (sold separately) faces in the horizontal direction to the rear and side to side. • A position where the lens part of the 2nd camera (sold separately) and the double-sided tape do not overlap the heating wires. • A position where the 2nd camera (sold separately) connection cable can be routed without unnecessary force. Rear windscreen Connection cable 2 Install this product. ① : Set the mounting bracket on the main unit. ② : Peel off the double-sided tape release paper from the mounting bracket. ③ : Install at the specified position of the front windscreen. 1 2 Front Windscreen 3 Firmly push ① this product. Heating wires 2nd camera (sold separately) Wiping range of the rear wiper 1 Clean the installation area of dirt and oils using the included cleaning cloth. ■ Front windscreen ■ Rear windscreen CAUTION • Make sure that the surface of the front windscreen is clean and dry before applying the tape. • Firmly push the area around the LCD. Next, remove this product from the mounting bracket, directly press the mounting bracket against the tape. In this way, the product can be firmly installed on the windscreen. • Never touch the surface of the LCD. • Use extreme care as the double-sided tape on the mounting bracket is extremely strong, and it will be difficult to reapply the tape once it has been applied. • To ensure the installation strength of the adhesive tape, leave this product for 24 hours after application before using it. 3 Install the 2nd camera (Only when installing the 2nd camera (sold separately)). ① : Peel off the double-sided tape release paper from the 2nd camera (sold separately). ② : Install in the specified position on the rear window so the image of the 2nd camera (sold separately) is displayed horizontally with the flat surface shown in the figure (the △ on the side faces up) facing upwards. Note • You can use the dedicated app to display the 2nd camera’s (sold separately) image horizontally to support installation. → “Exclusive App” 1 2 Install with the flat surface facing upwards. Turn the lens towards the outside of the vehicle and press down firmly so that the image of the 2nd camera (sold separately) is displayed horizontally. CAUTION • If the image of the 2nd camera (sold separately) is not displayed horizontally, it may not detect approaching vehicles behind correctly. 4 Connect the Dash Camera main unit, power cable, and 2nd camera connection cable (included with the 2nd camera (sold separately)). 2nd camera connection cable (included with the 2nd camera (sold separately)) 2nd camera (sold separately) Power cable This product Connection cable (included with the 2nd camera (sold separately)) 2nd camera (sold separately) 6 Connect the power cable. → “Connecting the Power Cable” 7 Turn the vehicle engine on to display the recording screen. 8 Adjust the angle of the lens so that video outside and inside the vehicle is properly displayed. This product Turn this part to adjust the lens angle. Main Unit 5 Route the power cable and 2nd camera connection cable (included with the 2nd camera (sold separately)) along the passenger side. Turn the angle adjustment jog dial to adjust the lens angle. 2nd camera (sold separately) During driving, turn the lens of this product towards the outside of the vehicle. This product restarts when the lens angle is moved from the outside of the vehicle to the inside, and vice versa. To switch between the Dash Camera main unit image and the 2nd camera (sold separately) image, press the button. → “Function Buttons” Note • A protective film is applied to the lens when the product is purchased. Peel off this film. アクセサリー ソケット シガーライター 電源ケーブル Connecting the Power Cable Be sure to disconnect the ⊖ terminal of the vehicle’s battery before connecting the power cable. By using the power cable to draw power directly from the vehicle, this product can detect and record vehicle movement caused by vibration even when the vehicle’s engine is turned off. Black 0.5 m Yellow 0.5 m Ground (Black) Securely connect to the metal part of the vehicle body. To prevent noise, connect as close to the navigation unit as possible. Fuse (F 2 AL/250 V) + Battery power supply (Yellow) Always connect to the power circuit supplied with power from the battery, regardless of whether the vehicle engine switch is ON or OFF. Red 0.5 m Fuse (F 2 AL/250 V) Accessory power supply (Red) Connect to the power circuit supplied with power when the vehicle engine switch is turned to the ACC position. Never install the accessory power supply to a vehicle that does not have an ACC position on the engine switch. Doing so may lead to a dead battery. 4.5 m Note: Connect the red and yellow lead wires to the terminals after wiring through the vehicle’s fuse unit. Connection Precautions To prevent fuming and damage to the product, be sure to first securely connect the black lead wire (Ground) of this product to the metal part of the vehicle body. Connect separate black lead wires (Ground) for products with a high current consumption such as a power amplifier. When setting up connections all at once, there is a risk of fuming or damage to the product when screws loosen or come off completely. *1 Black lead wire (Ground) *1 Metal part of the vehicle body *1 Not supplied for this unit
Download PDF file