English Part Names Top Left side 2 3 Front 1 Right side 4 7 8 Back 56 9 a b 1 Power Port Connect the cigarette lighter power cable or power and AV cable. 2 microSD card Slot 3 Reset Button Press this button with the tip of a ballpoint pen to reset this product. 4 LCD 5 Function Buttons 6 Lens 7 Speaker 8 System Indicator 9 Angle Adjustment Jog Dial The angle of the lens can be adjusted by turning this dial. a Microphone b Mounting Bracket Status Display The status display shows the operating status of this product. 1 2 3 45 6 7 8 00:00 1 Recording in progress 2 Elapsed recording time 3 Event recording status*1 4 Parking mode 5 Sound recording*2 6 Wi-Fi connection status*3 7 GPS reception status*4 8 Power status ( : Battery mode : Charging) *1 When manual event recording is performed or vibration is detected in the event recording mode, and event recording has been activated, “×2” is displayed. *2 A red “\” is displayed when sound recording is set to off. *3 During a Wi-Fi connection, this is displayed in green, and when Wi-Fi is disconnected, this is displayed in white. A red “x” is displayed when Wi-Fi connection is set to off. *4 During GPS reception, this is displayed in green, and when GPS cannot be received, this is displayed in white. In the parking mode, a red “x” is displayed since GPS reception is set to off. System Indicator Display The operating status of this product is displayed with the system indicator. System Indicator Illuminated green Illuminated red Blinking red Menu Displayed/ During Playback ― ― ― Video Recording ○ ― ― Recording Event ― ○ ― Error Has Occurred (Including microSD Card not Inserted) ― ― ○ Function Buttons The functions of the function buttons are indicated by the icons displayed at the bottom of the screen. The functions of the buttons will depend on the displayed screen. (Icons are not displayed on some screens.) In the playback screen or MENU screen, holding down the function button returns you to the previous screen. ■ Recording 1 Take photo 2 Main menu display 3 Manual recording of events 1 2 3 ■ During playback 4 Back 5 Pause (During photo file playback: Next file) 6 Delete 4 5 6 ■ During volume or sensitivity MENU screen display 7 Reduce volume and sensitivity 8 Confirm 9 Increase volume and sensitivity 7 8 9 Inserting and Ejecting the microSD Card Turn off the power to this product when inserting and removing the microSD card. Inserting the microSD Card Hold the top edge of the microSD card, position the microSD card so that the terminals are facing the backside of this product, and slowly insert it into the microSD card slot until it clicks. Ejecting the microSD Card Slowly push in the top edge of the microSD card until it clicks (1). The lock will be released. Pull out the microSD card (2). CAUTION Do not insert the microSD card at an angle. Doing so may cause damage. Exclusive App The exclusive app “Dash Camera Interface” can be used to check the video recorded on this product or make settings on the screen of an iPhone or smartphone (Android™). To use this app, a Wi-Fi connection must be made between this product and iPhone/smartphone (Android™) beforehand. 1 Set the Wi-Fi function of this product to on. 2 Operate the iPhone or smartphone (Android™) to select this product as the Wi-Fi connection device. The SSID name (access point name) and password of this product can be checked in the Wi-Fi settings screen. • Only one iPhone/smartphone (Android™) device can be connected to this product at any one time. When a second device is connected, the first connected device is disconnected. • While a Wi-Fi connection is made, no operations can be performed on this product. If a function button is pressed while a Wi-Fi connection is made, a message will be displayed prompting you to break the Wi-Fi connection. If you select [Yes], the Wi-Fi connection will be disconnected, and operations on this product will be enabled. • You can change the SSID name of this product by operating the exclusive app “Dash Camera Interface”. Note, however, when the SD card is formatted, the SSID name returns to its default setting. • It is recommended to enter the search term “Dash Camera Interface” in the search field to search for the application. Dash Camera Interface Check the Accessories Main Unit×1 Mounting Bracket×1 Cigarette Lighter Power Cable (5 m)×1 microSDHC Card (16 GB)×1 Quick Start Guide×1 Warranty×1 Cleaning Cloth×1 Installation Specified Installation Position on Front Windscreen When installing this product to the inside of the front windscreen, install in a vehicle and in a position that satisfies all of the following conditions. • A position where this entire product is within 20% of the top edge of the height of the front windscreen (range within 20% of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or is in the shadow of the rear view mirror as viewed from the driver’s seat. Note that “20%” as described above is a rough estimate. Please install the product in accordance with your country’s laws and regulations. • A position where the lens part of this product is within the wiping range of the wiper. • A position where the lens part of this product does not hang over the sunshade and black ceramic lines/black ceramic pattern. • A position where this product faces in the horizontal direction to the front and side to side. • A position where the power cable can be routed without unnecessary force. This product Installation Angle Forward Direction of Vehicle Allowable Installation Angle: 30˚ to 60˚ (With Lens Horizontal) Installation Direction This product Horizontal Direction Front Windscreend * Install this product in a location where it will not interfere with the driver’s field of view,such as behind the rear view mirror. Front Windscreen Within 20% of Height Ground This product Horizontal Direction A Pillar Rear View Mirror This product Range of Windscreen Wipers A Pillar Air Bag IMPORTANT Always install this product in the specified installation position to ensure a safe field of view while driving and to achieve full performance from the product. 1 Clean the installation area of dirt and oils using the included cleaning cloth 3 Route the cable Route the power cable to the passenger seat side. 2 Install this product ① : Set the mounting bracket on this product. ② : Peel off the double-sided tape release paper from the mounting bracket. ③ : Install at the specified position of the front windscreen. Front 1 Windscreen 2 Connect the power supply depending on its type. → “Connecting the Power Cable” 4 Turn the vehicle engine on to display the recording screen 5 Turning the angle adjustment jog dial, adjust the angle of the lens so that video outside and inside the vehicle is properly displayed 3 Firmly push this product. CAUTION • Make sure that the surface of the front windscreen is dry before applying the tape. • Firmly push the area around the LCD. Next, remove this product from the mounting bracket, directly press the mounting bracket against the tape. In this way, the product can be firmly installed on the windscreen. • Never touch the surface of the LCD. • Use extreme care as the double-sided tape on the mounting bracket is extremely strong, and it will be difficult to reapply the tape once it has been applied. • To ensure the installation strength of the adhesive tape, leave this product for 24 hours after application before using it. • Install firmly so that it does not come off. Incorrect installation may cause this to peel off while driving and cause an accident. Inspect the installation state from time to time. Angle adjustment jog dial During driving, turn the lens towards the outside of the vehicle. This product restarts when the lens angle is moved from the outside of the vehicle to the inside, and vice versa. Note A protective film is applied to the lens when the product is purchased. Peel off this film. Connecting the Power Cable Be sure to disconnect the ⊖ terminal of the vehicle’s battery before connecting the power or AV cable. Cigarette Lighter Power Cable Connection Fully insert this into the vehicle accessory socket to make a good connection. (The location of the accessory socket will differ depending on the vehicle.) Accessory socket Cigarette lighter power cable CAUTION The accessory socket will be extremely hot immediately after using the cigarette lighter. The tip of the cigarette lighter power cable may melt or short circuit if it is plugged in while the socket is hot. Wait for the socket to cool before plugging in the cigarette lighter power cable. Connecting the power / AV cable <RD-HWK100 (sold separately)> The parking mode (security mode allowing 24-hour, 365-day surveillance) can be used by extracting power directly from the vehicle by the power / AV cable. You can also connect the product to navigation by the power / AV cable to project realtime video from this product or movies and photos that are being played back on the screen of the navigation. Black Yellow 0.5 m 0.5 m Fuse (F 2 AL/250 V) Red 0.5 m Fuse (F 2 AL/250 V) 4.5 m Wiring specification of this product Audio is recorded in monaural sound. Audio (L) Audio (R) Ground Video Black 5 m Ground (Black) Securely connect to the metal part of the vehicle body. To prevent noise, connect as close to the navigation unit as possible. + Battery power supply (Yellow) Always connect to the power circuit supplied with power from the battery, regardless of whether the vehicle engine switch is ON or OFF. Accessory power supply (Red) Connect to the power circuit supplied with power when the vehicle engine switch is turned to the ACC position. Never install the accessory power supply to a vehicle that does not have an ACC position on the engine switch. Doing so may lead to a dead battery. Note: Connect the red and yellow lead wires to the terminals after wiring through the vehicle’s fuse unit. Video/audio output mini pin jack Connect to the AUX input of the main unit of a Pioneer product with a mini jack terminal compatible with video input. Connection to main units of other brands with RCA input terminals is also possible by using the included mini pin jack-RCA conversion cable (figure below). *After connecting, the following message is displayed: “Is the 3.5mm Audio/Video Jack Connected?” Select “Yes” or “No”. Yellow Video White Audio (L) Red Audio (R) 0.2 m Connection Precautions To prevent fuming and damage to the product, be sure to first securely connect the black lead wire (Ground) of this product to the metal part of the vehicle body. Connect separate black lead wires (Ground) for products with a high current consumption such as a power amplifier. When setting up connections all at once, there is a risk of fuming or damage to the product when screws loosen or come off completely. *1 Black lead wire (Ground) Metal part of the vehicle body *1 Not supplied for this unit QSG_VRECDZ600.indd 9-16 CYR1279-A < 5 > CYR1279-A < 6 > CYR1279-A < 7 > CYR1279-A < 8 > 2020/03/23 13:58:12
Download PDF file