English Part Names Top 10 Left side Front view 8 4 2 5 Right side 1 3 6 7 9 Back 1 Power Port Connect the cigarette lighter power cable. 2 microSD card Slot Up to 32GB microSD Card capacity 3 Reset Button Press this button with the tip of a ballpoint pen to reset this product. 4 LCD 5 Function Buttons 6 Lens 7 Speaker 8 System Indicator 9 Microphone 0 Suction Mount Cradle connection point Status Display The status display shows the operating status of this product. 1 2 1 Recording in progress 2 Elapsed recording time 3 Date / Time 3 System Indicator Display The operating status of this product is displayed with the system indicator. Blinking green Illuminated green Blinking green Not Illuminated Menu Displayed — — Normal Recording — — Recording Event — — Error Has Occurred (Including microSD Card not Inserted) — — Function Buttons The functions of the function buttons are indicated by the icons displayed at the bottom of the screen. The functions of the buttons will depend on the displayed screen. (Icons are not displayed on some screens.) In the playback screen or MENU screen, holding down the function button returns you to the previous screen. Recording 1 Main menu display 2 Manual recording of events (Event Recording) 3 Take photo 4 Playback recorded media 1 2 3 4 During playback 5 Back 6 Previous File 7 Next File 8 Delete 5 6 7 8 During MENU screen display 9 Back 0 Up ! Down " Confirm 9 0 ! " Inserting and Ejecting the microSD Card Turn off the power to this product when inserting and removing the microSD card. Inserting the microSD Card Hold the top edge of the microSD card, position the microSD card so that the terminals are facing the backside of this product, and slowly insert it into the microSD card slot until it clicks. Ejecting the microSD Card Slowly push in the top edge of the microSD card until it clicks ( 1 ). The lock will be released. Pull out the microSD card ( 2 ). Check the Accessories Main Unit ×1 Suction Mount Cradle x1 Quick Start Guide ×1 Warranty ×1 CAUTION Do not insert the microSD card at an angle. Doing so may cause damage. Cigarette Lighter Power Cable 3.5 m x1 Safety Strap x1 Installation Specified Installation Position on Front Windscreen When installing this product to the inside of the front windscreen, install in a vehicle and in a position that satisfies all of the following conditions. • A position where this entire product is within 20% of the top edge of the height of the front windscreen (range within 20% of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or is in the shadow of the rear view mirror as viewed from the driver’s seat. Note that “20%” as described above is a rough estimate. Please install the product in accordance with your country’s laws and regulations. • A position where the lens part of this product is within the wiping range of the wiper. • A position where the lens part of this product does not hang over the sunshade and black ceramic lines/black ceramic pattern. • A position where this product faces in the horizontal direction to the front and side to side. • A position where the power cable can be routed without unnecessary force. Installation Angle Forward Direction of Vehicle Installation Direction This product Horizontal Direction This product * Install this product in a location where it will not interfere with the driver’s field of view,such as behind the rear view mirror. Front Windscreend Within 20% of Height Front Windscreend Ground This product Horizontal Direction A Pillar Rear View Mirror This product Range of Windscreen Wipers A Pillar Air Bag IMPORTANT Always install this product in the specified installation position to ensure a safe field of view while driving and to achieve full performance from the product. Pioneer is not liable for any damage, due to installation or use of the product. 1 Clean the installation area 3 Route the cable Route the power cable to the passenger seat side. 2 Install this product 1 : Fix the Suction Mount Cradle to the Main Unit 2 : Install at the specified position of the front windscreen, adjusting the direction to make the image horizontal. Connect the power supply depending on its type. → “Connecting the Power Cable” 4 Turn the vehicle engine on to display the recording screen Note A protective film is applied to the lens when the product is purchased. Peel off this film. Connecting the Power Cable Cigarette Lighter Power Cable Connection Fully insert this into the vehicle accessory socket to make a good connection. (The location of the accessory socket will differ depending on the vehicle.) Accessory socket Cigarette lighter power cable CAUTION The accessory socket will be extremely hot immediately after using the cigarette lighter. The tip of the cigarette lighter power cable may melt or short circuit if it is plugged in while the socket is hot. Wait for the socket to cool before plugging in the cigarette lighter power cable. CAUTION • Make sure that the surface of the front windscreen is clean and dry, before attaching the cradle. • Firmly press the suction cradle installed on the windscreen. • Do not install the cradle by itself. Always use it connected with the Dash Camera. • Never touch the surface of the LCD. • Install firmly so that it does not come off. Incorrect installation may cause this to drop while driving and cause an accident. Inspect the installation state from time to time. • To avoid the windscreen mounted cradle from detaching, you may attach the safety strap (included in the box). microSDHC Logo is a trademark of SD-3C LLC. EU Conformity marking. UK Conformity marking.
Download PDF file