English Part Names Top 10 Left side Front 8 4 2 5 Right side 1 3 6 7 9 Back 1 Power Port Connect the cigarette lighter power cable. 2 microSD card Slot Up to 32GB microSD Card capacity. 3 Reset Button Press this button with the tip of a ballpoint pen to reset this product. 4 LCD 5 Function Buttons 6 Lens 7 Speaker 8 System Indicator 9 Microphone a Suction Mount Cradle connection point Status Display The status display shows the operating status of this product. 1 2 1 Recording in progress 2 Elapsed recording time 3 Date / Time 3 System Indicator Display The operating status of this product is displayed with the system indicator. System Indicator Menu Displayed Normal Recording Recording Event Illuminated green Blinking green Not Illuminated Error Has Occurred (Including microSD Card not Inserted) Function Buttons The functions of the function buttons are indicated by the icons displayed at the bottom of the screen. The functions of the buttons will depend on the displayed screen. (Icons are not displayed on some screens.) In the playback screen or MENU screen, holding down the function button returns you to the previous screen. ■ Recording 1 2 3 4 1 Main menu display 2 Manual recording of events (Event Recording) 3 Take photo 4 Playback ■ During playback 1 Back 2 Previous File 3 Next File 4 Delete 1 2 3 4 ■ During MENU screen display 1 Back 2 Up 3 Down 4 Confirm 1 2 3 4 Inserting and Ejecting the microSD™ Card Turn off the power to this product when inserting and removing the microSD card. Inserting the microSD Card Hold the top edge of the microSD card, position the microSD card so that the terminals are facing the backside of this product, and slowly insert it into the microSD card slot until it clicks. Ejecting the microSD Card Slowly push in the top edge of the microSD card until it clicks ( 1 ). The lock will be released. Pull out the microSD card ( 2 ). Check the Accessories Main Unit ×1 Suction Mount Cradle x1 Cigarette Lighter Power Cable (3.5 m/11 ft. 6 in.) ×1 Safety Strap×1 microSDHC Card (16 GB)×1 Quick Start Guide ×1 Warranty ×1 Note All images in this document are for illustrative purpose only and subject to change. Playing Recorded Files CAUTION Do not insert the microSD card at an angle. Doing so may cause damage. CAUTION Ensure care is taken when handling the microSD card, as it becomes hot after being written. 1 2 3 4 The thumbnails of files in the selected folder will be displayed. 1 Return to the previous menu 2 Previous file 3 Next file 4 Confirm Installation Specified Installation Position on Front Windshield When installing this product, install in a position that satisfies all of the following conditions if allowed by applicable law in your location: • Install in a 7-inch/17.8 cm square in the lower corner of the windshield farthest from the driver, a 5-inch/12.7 cm square in the lower corner of the windshield nearest to the driver and outside of any airbag deployment zone, or in a 5-inch/12.7 cm square mounted to the center uppermost portion of the interior of the windshield. The ideal location is behind the rearview mirror out of the driver’s view as shown below. • A position where this entire product is within 20 % of the top edge of the height of the front windshield (range within 20 % of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or is in the shadow of the rear view mirror as viewed from the driver’s seat. Note that “20 %” as described above is a rough estimate. Please install the product in accordance with your country’s laws and regulations. • A position where the lens part of this product is within the wiping range of the wiper. • A position where the lens part of this product does not hang over the sunshade or the black ceramic lines/black ceramic pattern. • A position where this product faces in the horizontal direction to the front. • A position where the power cable can be routed without unnecessary force. Installation Angle Forward Direction of Vehicle Installation Direction This product Horizontal Direction This product * Install this product in a location where it will not interfere with the driver’s field of view,such as behind the rear view mirror. Front Windshield Within 20 % of Height Front Windshield Ground This product Horizontal Direction A Pillar Rear View Mirror This product Range of Windshield Wipers A Pillar Air Bag IMPORTANT Always install this product in the specified installation position to ensure a clear view of the road while driving and to achieve full performance from the product. Pioneer is not liable for any damages due to faulty or improper installation or use of the product. Install this Product 1 Clean the installation area. 3 Adjust the installation angle. Loosen the angle adjustment nut to adjust. After adjusting, tighten the loosened nut to secure. Angle adjustment nut 2 Install this product. 1 Fix the Suction Mount Cradle to the Main Unit. 2 Install at the specified position of the front windshield, adjusting the direction to make the image horizontal. 4 Connect the cigarette lighter power cable to the main unit. Route the power cable to the passenger seat side. CAUTION • Make sure that the surface of the front windshield is clean and dry, before attaching the cradle. • Firmly press the suction cradle installed on the windshield. • Do not install the cradle by itself. Always use it connected with the Dash Camera. • Never touch the surface of the LCD. • Install firmly so that it does not come off. Incorrect installation may cause the unit to drop while driving, which may cause an accident. Inspect the installation state from time to time to ensure the unit remains securely attached. • To avoid the windshield mounted cradle from detaching, you may attach the safety strap (included in the box). 5 Turn the vehicle engine on to display the recording screen. Note A protective film is applied to the lens when the product is purchased. Peel off this film. 6 Installing the Safety Strap. 7 Removing this product. 1 Unhook the mounting cradle from the windshield. 2 Remove this product. 1 Hook the smaller loop of the safety strap around the Mounting Cradle where it connects to the Main Unit, and then connect the Mounting Cradle to the Main Unit. 2 Hook the larger loop of the Safety Strap around the Rear View mirror attached to the windshield. 3 Once the Safety Strap is connected to both the Rear View Mirror and the Dash Camera, attach the Dash Camera to the front windshield close to the location of the Rear View Mirror. Note Always install this Safety Strap as described. Do not cut the Safety Strap or install it in any other way than as described. Pioneer is not liable for any damage, due to installation other than described, or use of the product. Connecting the Power Cable Cigarette Lighter Power Cable Connection Fully insert this into the vehicle accessory socket to make a good connection. (The location of the accessory socket will differ depending on the vehicle.) Accessory socket Cigarette lighter power cable Passenger footwell area CAUTION The accessory socket may be extremely hot immediately after using the cigarette lighter. Also, the tip of the cigarette lighter power cable may melt or short circuit if it is plugged in while the socket is hot. Wait for the socket to cool before plugging in the cigarette lighter power cable. Trademarks & Copyrights • SD, microSD and microSDHC Logo are trademarks of SD-3C LLC.
Share
Print
Download PDF file
