English Parts supplied Connecting the in-vehicle product using the MHL adapter HDMI cable (Type A - A) 1.5 m (4 ft. 11 in.) MHL adapter OF •This product cannot be installed in a vehicle without ACC (accessory) position on the ignition switch. OF Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. WARNING: Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash hands after handling. Important safeguards This manual explains how to connect the in-vehicle product via the connectivity kit. For details of the operation of the connected product, refer to another manual. •Read this manual fully and carefully before installing this product. •Keep this manual handy for future reference. •Pay close attention to all warnings in this manual and follow the instructions carefully. •Do not install this product where it may (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems of safety features, including airbags, hazard lamp buttons, or (iii) impair the driver’s ability to safely operate the vehicle. In some cases, it may not be possible to install this product because of the vehicle type or the shape of the vehicle interior. •Make sure that the cables and wires are routed and secured so they will not interfere with or become caught in any of the vehicle’s moving parts, especially the steering wheel, shift lever, parking brake, sliding seat tracks, doors, or any of the vehicle’s controls. Specifications Power source .14.4 V DC (10.8 V to 15.1 V allowable) Max. current consumption .1 A Operation temperature range .–10 ºC to +60 ºC (+14 ºF to +140 ºF) Storage temperature range .–20 ºC to +80 ºC (–4 ºF to +176 ºF) Dimensions Power supply box (W×H×D) .56 mm × 25 mm × 74 mm (2-1/4 in. × 1 in. × 2-7/8 in.) MHL adapter (W×H×D) .41 mm × 15 mm × 45 mm (1-5/8 in. × 5/8 in. × 1-3/4 in.) Weight Power supply box .120 g (0.3 lbs) MHL adapter .50 g (0.1 lbs) Note: Specifications and design are subject to possible modifications without notice due to improvements. F ACC O N STAR F O N STAR Power supply box × 1 MHL adapter × 1 Adapter cable (HDMI Type A - D) × 1 0.75 m (2 ft. 6 in.) HDMI terminal USB - micro USB cable (Type USB A - micro USB B) 2.25 m (7 ft. 5 in.) ACC position No ACC position HDMI cable (Type A - A) × 1 USB - micro USB cable (Type USB A - micro USB B) × 1 Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function. •When replacing the fuse, be sure to only use a fuse of the rating prescribed on this product. •This product is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. •To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning installation. •Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, parking brake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. •Secure the HDMI cable using the holder provided with your vehicle’s unit. •As the power box can heat up, it should never be installed in the following locations: – where it could come into contact with car wiring or equipment – where it would easily come into contact with passengers. Power supply box Fuse (2 A) Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF Black (ground) To vehicle (metal) body •Use only the cables included in this connectivity kit to ensure proper connection. •Do not use the cables included in this connectivity kit for other models. Connecting the in-vehicle product using HDMI cables HDMI cable (Type A - A) 1.5 m (4 ft. 11 in.) Adapter cable (HDMI Type A - D) 0.75 m (2 ft. 6 in.) Notes: •The positions of the HDMI terminals differ depending on the in-vehicle product. For details of the terminals’positions, refer to the manual of each product. •The adapter cable (HDMI Type A-D) will not be used if you use the MHL adapter. Installing the power supply box HDMI terminal USB - micro USB cable (Type USB A - micro USB B) 2.25 m (7 ft. 5 in.) 1 Decide on the installation position. Power supply box Notes: • Thoroughly wipe off the surface before affixing the adhesive tape. • Use separately sold adhesive tapes to secure this product so that it does not move. It is extremely dangerous if cords are exposed on the floor as they may become entangled with the brake pedal etc. Hide cords so that they do not get in the way when you are driving. • Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed. Power supply box Notes: •The positions of the HDMI terminals differ depending on the in-vehicle product. For details of the terminals’ positions, refer to the manual of each product. •The MHL adapter will not be used if you use the adapter cable (HDMI Type A-D). Fuse (2 A) Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF Black (ground) To vehicle (metal) body Adhesive tape (sold separately) 2 Attach the power supply box using separately sold adhesive tapes. T T
Download PDF file